Automation VMR

In the two-day training course, participants carry out the entire measuring procedure in the VMR and create a complete measurement program offline that is subsequently run in the ATOS ScanBox.

The Virtual Measuring Room (VMR) is a control and measurement planning software consisting of a virtual and functional representation of the real measuring environment. With appropriate licensing, the VMR is already included in the software.

After a comprehensive introduction to the VMR, participants learn how to position the measuring setup reproducibly. The inspection planning imparts the functional principle of the automatic position generation. Based on the imported measurement plan and CAD data, participants learn how to create ATOS measurement positions and photogrammetry measurement positions along with the corresponding robot paths automatically.

While the measurement series are executed, the so-called burn-in process takes place. This means that the software automatically defines and saves the individual measurement parameters for each measurement, such as the exposure time or reflection detection.

The participants complete the measuring project by creating a project template and gain insight into the Kiosk Interface, a special user interface for simplified operation of the ATOS ScanBox that can be used for component testing in series production.

Target groupGOM advanced users
SystemATOS ScanBox or an automated project cell
ATOS Professional VMR or GOM Inspect Professional VMR software
PrerequisitesSuccessful completion of ATOS Professional System Basic Training
Duration2 days
CertificationAutomation VMR
after completion of the training

GOM Training Center

Find the complete offer of all classroom training courses in your country.
Enroll in eLearning courses to learn at your own pace at any time and in any place in the world.

Create your personal account to view your completed courses, achievements and certificates as well as the presentations and demo data for your training courses.

ENROLL

Course content

  • Operation of the virtual measuring room
  • Reproducible simulation of the real measuring setup in the virtual measuring room
  • Fully automatic teaching of the robot
  • Automated measurement planning
  • Real movements and measurements in the VMR
  • Virtual positioning of the CAD model
  • Using the ATOS sensor in combination with the photogrammetry camera in the VMR
  • Measuring the top and bottom side of a measuring object
  • Working with and without fixtures
  • Working with project templates

Braunschweig
GOM GmbH,
Schmitzstraße 2

  • November 21 - November 22, 2019 Week 47)
  • December 19 - December 20, 2019 (Week 51)
  • January 16 - January 17, 2020 (Week 03)
  • January 30 - January 31, 2020 (Week 05)
  • March 05 - March 06, 2020 (Week 10)
  • April 02 - April 03, 2020 (Week 14)

Additional dates on request.

 

Leipheim
GOM Süd, Wilhelm-Röntgen-Straße 11

  • December 12 - December 13, 2019 (Week 50)
  • January 30 - January 31, 2020 (Week 05)
  • February 13 - February 14, 2020 (Week 07)
  • March 12 - March 13, 2020 (Week 11)
  • April 02 - April 03, 2020 (Week 14)

Additional dates on request.

Austria

On request

Belgium

On request

Brazil

On request

China

On request

Croatia

On request

Czech Republic

On request

Denmark

On request

Finland

On request

France

On request

Hungary

On request

Ireland

On request

Italy

On request

Japan

On request

Kasakhstan

On request

Macedonia

On request

Mexico

On request

Norway

On request

Poland

On request

Portugal

On request

Russia

On request

Serbia

On request

Slovakia

On request

Slovenia

On request

Spain

On request

Turkey

On request

Ukraine

On request

United Kingdom

On request

USA

On request

Learning Concept

GOM training courses follow a standardized concept, which was developed in cooperation with customers and partners from all over the world. The immediate vicinity to GOM’s development facilities guarantees a high standard of training contents and a direct link to practice.